Motion Sensor Light Switch Adjustment PIR Motion Sensor Switch LED Driver Controller
|Model NO.||led driver controller|
motion sensor light switch adjustment pir motion sensor switch led driver controller
1. New design, small volume, light weight, flame retardant insulation ABS+PC shell,
2. AC/DC step-down, constant voltage and constant current circuit design, over voltage, over current, overload, short circuit protection,
3. The output voltage is DC12V/24v 24W 36W 40W 60W 100W 150W, 24W : 6 DuPont output interfaces +1 sensor switch interface ,36W 40W 60W:5 DuPont output interfaces +1 sensor control interface + 1 serial control interface ,100W 150W: 10 DuPont output interfaces +1 sensor control interface, compatible with 4 kinds of sensor switch control: 1. touch sensor switch, 2. door sensor switch, 3. hand sweep sensor switch, 4. PIR sensor switch.
4. Suitable for cabinet light power supply, display cabinet LED power supply, wine cabinet light LED drive, LED wall light belt driver, decorative light strip power supply, etc.
5. In order to meet the needs of different customers, we have developed a variety of models with 12V, 24V, 12W to 100W duPont interfaces in led strip remote pir light switch led power supply 18w
6. If you have different needs, we have 13 years of software(especially MCU Chip) programming engineers, there are more than 1600 squar patches, plug-in welding workshop factory, can be for you from software programming to PCB design proofing, PCB SMT processing and finished product assembly supporting, to achieve a one-stop service.
|Model||led driver controller|
|Input voltage range||AC110-240v|
|Output voltage||12V DC|
|Output current||2A,3.33A, 5A, 8.33A, 12.5A|
|Output rated power||24W 36W 40W 60W 100W 150W|
|Max load voitage||14V|
|Seismic performance||10~500Hz,2G 10min,/1 cycle, length 60 minutes, each axis|
|Surge currentLeakage current||65A 230Vac in full-loaded cold state(max)|
|Voltage adj range||±3%|
|Setup, rise, hold up time||200ms,50ms,20ms|
|Protection||Overload, overvoltage, overcurrent, short circuit protection|
|Operating temperature humidity||-20ºC~+60ºC,20%~90%RH|
|Storage temperature humidity||-20ºC~+60ºC,10%~95%RH|
|Product size||160 x 60 x 20MM|
|Product name||led driver 12v 100w|
How to choose suitable switching power supply?
1. Set the power supply voltage. Confirm the input voltage of the application product (AC: AC; DC: DC) Select the power supply with the same voltage as the application product. Equipment voltage by current = equipment power: 12 v (voltage) x 10 a (current) = 120 w (power) or: 120 w (power) present 12 v (voltage) = 10. A (current). Equipment power ÷80%= power supply.
For example :1.LED products: the power of 80W must be powered by a power supply of more than 10Ow.
2. Motor machinery: 100W power, must use more than 200W power supply; Due to other corresponding circuits in the inner cover of related products, the instantaneous start current is required to be too large.The selection of power supply power must be strictly in accordance with 80% selection, not less than or the same as the product power; The voltage is consistent, the power is large, can be used.
2. Common problems and misunderstandings in power supply selection .
Q: Does the power supply consume too much power?
A: For example,100 watts of power supply,100 watts refers to the maximum load power value, not the operating value after starting; The power consumption of the product is determined by the power of the product and has nothing to do with the power of the power supply.
Q: Did you buy a large burner for the power supply?
A: The power supply is only responsible for voltage conversion, as long as the corresponding voltage is selected, there is no burning lamp and other problems.
Q: Can we use 24V transformer for 12V voltage? Or can both be used?
A: no, for example, the product voltage 12 VOLTS must use 12 volt power supply. Q: The newly bought power supply does not work after it is switched on? Answer: Generally wiring problem, please check the line or timely contact customer service.
3. Note: The power supply power must be greater than the power of the equipment. Lay person Please install under the condition of personal safety, do not work with electricity.
1. Are you a trading company or factory?
We are a 13 years PCB design and assembly experience factory in Shenzhen.
2. Do you provide samples?
Yes, free samples are provided while you pay the freight. We have a small amount in stock all year round.
3. What's your MOQ?
Our MOQ is 1000pcs, but for the first order, there is no MOQ.
4. How long is the lead time?
It takes about 15-25 working days to proceed mass production. For samples, it's usually in a week.
5. What's your payment term and shipping term?
Advanced T/T & FOB Shenzhen / Dongguan / Hongkong
6. How long is the warranty?
It's 2~5 year,depending on what kind of product's performance the customer wants.